An extruded high-density polyethylene drainage core with a non-woven filter fabric bonded to the ridges of the geonet. The filter fabric retains soil or sand particles as well as freshly placed concrete or grout, allowing filtered water to pass into the form to irregular surfaces. Because of this crush-proof nature, geonet drainage composites can be used in the most extreme cases with heavy loads and/or heavy vehicular traffic, both horizontally and vertically.
Consisst of a heavy-duty, high-density polyethylene geonet drainage core with its ridges heat fused to a layer of non-woven filter fabric. The filter fabric retains soil or sand particles as well as freshly placed concrete or grout, allowing filtered water to pass through to the drainage core. J-DRain 300 provides drainage from one side only.
J-DRain 302
Identical to J-Drain 300 in physical properties with the addition of a layer of filter fabric to the back side providing drainage and filtration from both sides.
J-DRain 1000
Identical to J-Drain 300 in physical properties with the addition of a layer of coated fabric bonded to the back side providing protection for waterproofing systems requiring a protection layer.
Consists of an impermeable polymeric sheet cuspated under heat and pressure to form a high flow dimpled drainage core. The core is bonded to a layer of filter fabric (available with a woven or non-woven filter fabric). The filter fabric retains soil or sand particles as well as freshly placed concrete or grout, allowing filtered water to pass into the drainage core.
J-DRain 200
Consists of a light-duty impermeable polymeric sheet cuspated under heat and pressure to form a high-flow dimpled drainage core. The core is then bonded to a layer of non-woven filter fabric. The filter fabric retains soil or sand particles as well as freshly placed concrete or grout, allowing filtered water to pass into the drainage core. Limited to 20 feet of backfill.
J-DRain 220
The identical properties as J-DRain 200 with the addition of a protection sheet bonded to the back side of the cuspated core providing protection for soft membrane waterproofing systems. J-DRain 220 is compatible with waterproofing systems without the use of a protection board. Limited to 20 feet of backfill.
J-DRain 400
Consists of a moderate-duty impermeable polymeric sheet cuspated under heat and pressure to form a high-flow dimpled drainage core. The core is then bonded to a layer of non-woven filter fabric. The filter fabric retains soil or sand particles as well as freshly placed concrete or grout, allowing filtered water to pass into the drainage core.
J-DRain 420
The identical properties as J-Drain 400 with the addition of a protection sheet bonded to the backside of the cuspated core providing protection for soft membrane waterproofing systems. J-Drain 420 is compatible with waterproofing systems without the use of a protection board.
J-DRain 700
Consists of a heavy-duty impermeable polymeric sheet cuspated under heat and pressure to form a high-flow dimpled drainage core. The core is then bonded to a layer of woven filter fabric. The filter fabric retains soil or sand particles as well as freshly placed concrete or grout, allowing filtered water to pass into the drainage core.
J-DRain 720
The identical properties as J-DRain 700 with the addition of a protection sheet bonded to the backside of the cuspated core providing protection for soft membrane waterproofing systems. J-Drain 720 is compatible with waterproofing without the use of a protection board.
J-DRain-it Interior Foundation Drain
An interior drainage system consisting of an L-Shaped dimple core that is installed against a foundation wall and on top of the footing prior to the placement of the basement slab. This provides an opening for water to escape to the gravel fill under the basement slab. This excess water is taken to daylight or to a sump for removal.
J-DRain VCS: Vertical Collection System
J-DRain VCS Vertical Collection System for Foundation Walls is a high-profile vertical collection system used for the disposal of water collected by J-DRain® Prefabricated Drainage Composites. It is used at the base of foundation walls and eliminates the typical pipe and gravel collection system. J-DRain VCS comes complete with a full array of fittings for easy connection to typical 4" sewer pipe to transmit collected water to daylight or sump.
J-DRain SWD-6 Modular Drainage System
J-DRain SWD-6 is a modular composite drainage and collection system consisting of a 3-dimensional, high-flow, drainage core which is wrapped with a non-woven filter fabric. It is designed to replace a conventional sand or gravel covered pipe drain around building foundations and retaining walls. Soil particles are held back by the filter fabric allowing water to pass through to the drain core for easy removal by sump or by running to daylight. Available in 6 inch and 12 inch widths. A full array of fittings are available in the system to allow for a fast and easy installation.
J-DRain SWD Composite Turf Drainage System
J-DRain SWD is a composite turf drainage system consisting of a 3-dimensional, high flow, drainage core and a non-woven, needle-punched filter fabric. The filter fabric is wrapped and bonded to the drainage core, preventing intrusion of the filter fabric into the flow channels during the backfilling process. Soil particles are held back by the filter fabric and water passes through to the drainage core allowing water to be collected and conveyed to the discharge point. Available in 6 inch and 12 inch widths. Roll lengths are 150 feet.
Visit the Product Data Sheets and Specifications page for additional downloadable information.
NES evaluated.
Report No. NER-636
